building a new bicycle

Started by Helen, Feb 12, 2012, 09:08 PM

Previous topic - Next topic

Helen

Here in the picture you see every single darn piece you need to assemble a bike. I will have the wheels built for me, and the rest I'll do myself.

I'm locking this so I can have sequential updates of the build progress, then I'll unlock it.

One of the Scriveners.

Helen

#1
Here is the frame I'm going to use. Sorry about poor pic. I'll make sure to have a decent one when it's finished.

A couple of cool things about this frame. It is a 1991 specialized stumpjumper S-works. It was also NEVER BUILT! So essentially I got a '91 frame in mint condition. How awesome is that?

Cool thing number two. I purchased it from Eschen, Liechtenstein. This is a very small country (62 square miles) located in Europe. It is bordered by switzerland and austria, and it is ruled by a prince.

So maybe I'll call the bike Princess  :)

One of the Scriveners.

Helen

#2
Headset/fork done. The cups and race were already on (luckily, since I don't have the tool to put them on), and the headset was brand new, so I just greased it up and put it on.

Minor drawback, I need to put on a front brake cable hanger on the steerer tube, but the steerer tube is cut pretty short, I'm going to have to find a cable hanger that is only 2mm thick. I haven't seen one on the net. They don't make 1inch headset tubes anymore, I have to find old stock.

One of the Scriveners.

Helen

Bottom bracket done. Went on beautifully. So easy. My first one. I think externally threaded bbs must be easier. Or probably it was the fact it was sealed and I didn't have to mess with bearings.

One of the Scriveners.

Helen

The top steerer tube is cut pretty short, leaving me very little space to add a front cable hanger. I needed one where the ring is only 2mm thick. Couldn't find one online, so I put together some parts lying around and took them to the local bicycle commuters yard, and donated my parts so I could scrounge through their parts. I managed to find one off a 10-speed.

One of the Scriveners.

Helen

#5
Stem and handle bar on, also the front cable hanger, now painted black. Handlebar was cut to a length of 20 inches.

One of the Scriveners.

Helen

One of the Scriveners.

Helen

Brake cantilevers on. For those with a fine eye, yes I have my brake shoes reversed. This, plus "toeing" them in towards the front, gives me superior and quieter stopping power, IMO.




One of the Scriveners.

Helen

Brake levers and shifters on.

One of the Scriveners.

Helen

Cable housing and wiring all done for brakes.

One of the Scriveners.

Helen

Cranks, before and after




One of the Scriveners.

Helen

Some cassettes come apart easily with an allen key. Others you need to punch the rivets out. And still others, like mine, need the old grinder!

So I took mine apart with a grinder and I wrecked the largest sprocket in the process. That's ok, I just went to bike store to buy a spare.

Why take it apart? My shifters are these '90-'95 shimano 7speed index thumbshifters. Though 7speed, they came with a magical 8th shifting slot. So hypothetically you should be able to use an 8 speed cassette right? Unfortunately the 7 speed indexing does not give you smooth shifting with an 8 speed cassette. Solution (sort of), take apart the cassette and put wider spacers in-between the sprockets.

But I have another limitation, my rear hub is for a 7/8 speed cassette, meaning there is not much wiggle room when making the cassette wider. Here's the sprocket/spacer combination I used to get smooth shifting.


sprocket 30 T (tooth)
spacer3 mm
sprocket 26 T
spacer3.28 mm
sprocket 23 T
spacer3.5? mm (estimated)
sprocket 20 T
spacer3.5? mm (estimated)
sprocket 17 T
spacer3 mm
sprocket 15 T
spacer3 mm
sprocket 13 T
sprocket 11 T (with attached spacer)

The two estimated ones did not have a number stamped on them, but visually I could see they were wider. I got these by again going to the bicycle commuter store and rummaging though old cassettes. I walked away with 6 hard-to-find spacers for $2, can't beat that :)


One of the Scriveners.

Helen

Rear derailleur and chain.

One of the Scriveners.

Helen

One of the Scriveners.

Helen

Bar ends and grips.

One of the Scriveners.

Helen

One of the Scriveners.

Helen

Seat and bottle cage. Wow, done! Time for some showroom pics.

One of the Scriveners.

Helen

#17
introducing princess.

Click on pics for larger image.

Thread now open for posts.





































princess and deirdre



One of the Scriveners.

Hermskii

That chain looks special. does is even need lube?
~Peace~

Hermskii

Helen

lol it's just brand new. It does come with a slight lubrication coating. But I'll oil it it up before the first ride.
One of the Scriveners.